Fiat 128 Features, Photos and Videos

The Fiat 128 is a tranverse front-engine, front wheel drive small family car manufactured and marketed by Fiat from 1969 to 1985 as a two- or four-door sedan, three- or five-door station wagon as well as two- or three-door coupé. The 128 running gear and engine, reconfigured for a mid-engined layout, were used in the Fiat X1/9 sports car.

Named European Car of the Year in 1970, over three million were manufactured.

The 128 was noted for its innovative front-engine, front-drive layout, which enabled an especially large interior volume and ultimately became the predominant front engine/drive layout, worldwide. In 2012, noted automotive journalist Jamie Kitman called the 128 a "pioneer of the small cars we drive today."

With engineering by Dante Giacosa and engine design by Aurelio Lampredi, the 128 was noted for its relatively roomy passenger and cargo volume — enabled by a breakthrough innovation to the front-engine, front-drive layout which became the layout "adopted by virtually every other manufacturer in the world" for front-wheel drive. Fiat promoted in its advertising that mechanical features consumed only 20% of the vehicle's volume and that Enzo Ferrari drove a 128 as his personal vehicle."

Fiat built an entirely new plant in Rivalta, north-west of Turin, specifically to manufacture the new 128.

Front-wheel drive had previously been introduced to small, inexpensive cars with the British Mini, and then with the larger 1100/1300 series, which Fiat set about designing a new car to compete with during the mid 1960s. As engineered by Alec Issigonis, the compact arrangement located the transmission and engine sharing a single oil sump — despite disparate lubricating requirements — and had the engine's radiator mounted to the side of the engine, away from the flow of fresh air and drawing heated rather than cool air over the engine. The layout often required the engine be removed to service the clutch.

As engineered by Dante Giacosa, the 128 featured a transverse-mounted engine with unequal length drive shafts and an innovative clutch release mechanism — an arrangement which Fiat had strategically tested on a previous production model for a full five years, the Primula from its less market-critical subsidiary, Autobianchi. The layout enabled the engine and gearbox to be located side by side without sharing lubricating fluid while orienting an electrically controlled cooling fan toward fresh air flow. By using the Primula as a test-bed, Fiat was able to sufficiently resolve the layout's disadvantages, including uneven side-to-side power transmission, uneven tire wear and potential torque steer, the tendency for the power of the engine alone to steer the car under heavy acceleration.

The compact and efficient layout — a transversely-mounted engine with transmission mounted beside the engine driving the front wheels through an offset final-drive and unequal-length driveshafts — subsequently became common with competitors and arguably an industry standard.

The layout was sufficiently flexible that Fiat reconfigured the 128 drive-train as a mid-engined layout for the Fiat X1/9.

The all new 1.1 litre Fiat SOHC engine, engineered by noted engine designer Aurelio Lampredi, featured an iron block mated to an aluminum head along with a belt-driven single overhead camshaft producing 49 hp.

The 128 was styled similarly to the 124 and 125 and featured rack-and-pinion steering, front disc brakes, independent rear suspension with a transverse leaf spring, and a strut-type front suspension with integral anti-roll bar.

Initially, the 128 was available as a two-door or four-door sedan. At the 1970 Turin Motor Show a three-door station wagon model called "Familiare" was added to the line-up. The car was only available with a 1116 cc engine on launch, though the two-door-only 128 Rally edition launched in 1971 used a 1,290 cc unit. Also in 1971, the Sport Coupé, an all-new coupé body on a shortened 128 platform, was unveiled at the Turin Show. On launch it was available with both existing 128 engines.

The 128 range underwent a facelift in 1972, featuring a revised grille. 1974 saw the launch of the 128 Special, which used the Rally engine in a four-door sedan body. In 1975 the 128 3P (3-door) Berlinetta replaced the Sport Coupé. In 1976, the range received new bumpers, rectangular headlights, tail lights and dashboard as well as modifications to the engines. At this time, the wagon was also renamed the "Panorama".

Production of all 128s except that of the base 1,100 cc powered model ended in 1979 after the introduction of the Fiat Ritmo/Strada in 1978. In 1980 production of the small three-door station wagon Panorama was dropped from the range and 128 production finally ended in 1985.

The British "Motor" magazine tested a Fiat 128 in April 1970, shortly after its UK launch. The car had a top speed of 85.4 mph (137.4 km/h) and accelerated from 0-60 mph (97 km/h) in 15.5 seconds. An "overall" fuel consumption of 27.5 miles per imperial gallon (10.3 L/100 km; 22.9 mpg‑US) was recorded. This put it fractionally behind the contemporary Morris 1300 on maximum speed but usefully ahead on acceleration. The two were closely matched on fuel economy, where both were outrun by the Ford Escort 1300 Super also included in the comparison, here in its four-door version. The Fiat's £876 manufacturer's recommended price was not too far above the Morris 1300's £830 and the Escort's £838. The testers commended the Fiat's interior space and excellent performance. Wind and road noise were low, but engine noise was not.

The Fiat 128 Rally was a sporty, 1.3-litre-engined version of the 128 two-door saloon, introduced at the 41st Geneva Motor Show in March 1971 and produced up to 1974.

Compared to the regular 128's 1,116 cc four-cylinder engine, the Rally's type 128 AR engine had been bored out 6 mm to 86 mm—while keeping the 55.5 mm stroke—for a total displacement of 1,290 cc (79 cu in). There was also a twin-choke Weber 32 DMTR carburettor, revised valve timing and a slightly higher 8.9:1 compression ratio. Engine output was now 67 DIN-rated metric horsepower (49 kW; 66 hp) at 6,200 rpm and 88 DIN-rated newton metres (65 lb⋅ft) of torque at 4,000 rpm.Other mechanical improvements were the addition of a vacuum servo, an engine protection plate, better tyres, new gear ratios for the 4-speed transmission, a higher capacity battery and an alternator in place of the dynamo).

A number of exterior features set the Rally apart from other 128s. At the front there was a black radiator grille, carrying the round Fiat emblem typical of the marque's sports cars; split bumpers joined by a tubular steel bar; and halogen headlamps and bumper-mounted auxiliary lamps. At the rear dual round tail lamps replaced the square ones found on the regular two-door 128. "Rally" badging on the bonnet and boot lid and stripes along the side sills completed the sporty look.The interior was upholstered in black leatherette, and the dashboard housed upgraded instrumentation: a tachometer was standard equipment, and water temperature and oil pressure gauges took the place of the ashtray, relocated to the centre console. Front sports seats with headrests and a two-spoke sports steering wheel replaced the standard items.

In October 1972 Fiat introduced several updates to the whole 128 saloon and Familiare range, including the 128 Rally. In particular the Rally received new upholstery (leatherette with cloth seat centres) and a black plastic protection to the front bumper tube.

At the 53rd Turin Motor Show of November 1971 Fiat introduced the 128 Coupé, also called 128 Sport, a 2-door, 4-seat coupé based on a shortened 128 chassis. It was produced until 1975, when it was replaced by the 3-door 128 3P.

Complete article available at this page.