Princess (car) Specifications, Photos and Videos

The Princess is a family car which was produced in the United Kingdom by the Austin-Morris division of British Leyland from 1975 until 1981 (1982 in New Zealand). The car inherited a front-wheel drive / transverse engine configuration from its predecessor, the BMC ADO17 range. This was still unusual in Europe for family cars of this type and gave the Princess a cabin space advantage when compared with similarly sized cars from competing manufacturers.

The car, which had the design code ADO71, was originally marketed as the Austin / Morris / Wolseley 18–22 series. In 1975 the range was renamed "Princess". This was effectively a new marque created by British Leyland, although it had previously been used as a model name on the Austin Princess limousine from 1947 to 1956, and the Vanden Plas Princess. The Princess is often referred to, incorrectly, as the Austin Princess. Although this name was not used in the UK market, it was used in New Zealand. The car was later revamped as the Austin Ambassador, a hatchback, which was produced from 1981 until 1984 and only available in Britain and Ireland.

Princess sales, although initially strong, were tailing off by the end of the 1970s. Some of its competitors had gained a fifth-door as a hatchback which the Princess lacked (though Harris Mann originally designed the car with a hatch) and the medium large-car sector fell victim to a poor economic climate further compounded by the OPEC oil crisis of the day. It was somewhere between the Ford Cortina and Ford Granada in terms of size, being designed to compete with more expensive versions of the Cortina as well as entry-level versions of the Granada. British Leyland restyled the Princess with a boot so that it would not compete with their existing SD1 and Maxi designs.

The limousine version was devised in late 1975 and produced on a small scale by Woodall Nicholson. Based on the top of the range Princess 2200 HLS, stretched at the B-pillar to allow more room for the rear compartment, the front door remained unchanged, making the car look oddly proportioned from the side. The Leyland Princess 2200 HLS Limousine was produced between 1975 and 1979, and was mostly sold to local borough councils (as a mayoral car) and to the funeral sector. Princess limousine seemed to be an alternative to a Daimler DS420 that local government used in the mid 70s as Daimlers were much more expensive.

Total production amounted to 224,942 units.

The car was launched on 26 March 1975 as the 18–22 series, "the car that has got it all together". The number designation 18–22 referred to the engine sizes available carried forward from the 1800 cc and 2200 cc BMC B-series-engined BMC ADO 17 "Landcrab". For the first six months of production three badge-engineered versions were produced: Austin, Morris and Wolseley. The Austin model bore the original "design intent", featuring trapezoidal headlights and a simple horizontally-vaned grille. The Morris and Wolseley cars had a raised "hump" permitting a larger, styled grille for each model; the Morris one was a simple chrome rectangle with Morris in the lower right-hand corner, while Wolseleys had a chrome grille with the traditional illuminated company logo, with narrower vertical bars either side set back within the chromed surround. Both of these versions had four round headlights, and the Wolseley model was only available with the six-cylinder engine and luxury velour trim. Apart from their bonnet and headlamp designs, and of course their badging, the Austin and Morris models were virtually identical.

The exterior styling was distinctive, innovative, and somewhat divisive. "The Wedge", as it was often nicknamed, was indeed very wedge-shaped; the styling was all angles and slanting panels. This was very much a 1970s design as created by Italian stylists (see Lamborghini Countach for example). Within BL the car was often referred to as "The Anteater". The designer, Harris Mann, was also responsible for the Triumph TR7, another wedge-shaped car, as was his original design for the Austin Allegro, although by the time that design had been readied for production nearly all the angular styling features had been lost.

The Princess, unlike the Allegro, made it to regular production relatively unscathed and unaltered from Harris's original plan. The bonnet (hood) was a little higher, to allow for taller engines, but the biggest change from Harris's design involved the rear. Harris had intended the design to be a five-door hatchback, but management decided that the Austin Maxi should be the only hatchback in the range, making that its unique selling point, and besides, they thought the Princess's prospective buyers would dislike a hatchback – despite the fact that in the Rover division the larger Rover SD1 was being given a hatchback design. Consequently, the Princess received fixed rear glass and a separate boot, belying its appearance. An estate version was also proposed, but never reached production.

The base engine fitted was the 1798 cc B-series pushrod straight-4. The lay-out closely followed that of the predecessor model, but access to the alternator/water pump was greatly improved by exploiting the car's longer nose to fit a front-mounted radiator. The basic design of the engine dated back to 1947 and the unit with a claimed output of 84 bhp was notably lacking in power, although torque was reasonable. The larger engine, fitted to upper models in the range, was a 2227 cc E-series SOHC straight-6. This was very smooth and a much more modern engine, with a published output figure of 110 bhp, but was still not hugely powerful. The Princess was a big car, and the engine choice gave lacklustre performance, not helped by the provision of only a 4-speed manual gearbox (a Borg-Warner automatic transmission was an option). Suspension used BL's Hydragas system.

A six-cylinder car was road tested by Britain's Autocar magazine in March 1975 at the time of the model's launch. It recorded a maximum speed of 104 mph (167 km/h) and reached 60 mph (97 km/h) from a standing start in 13.5 seconds. The top speed was marginally lower than the 109 mph (175 km/h) achieved by a recently tested Ford Consul 2500 L and a full three seconds slower to 60 mph than the Ford which managed the standing start test in just 10.4 seconds. The 2200 also fell slightly behind the Fiat 132GLS 1800 in these comparisons. At the same time its overall fuel consumption at 20.7 mpg was usefully superior to the Ford's 18.1 mpg. The lighter Fiat was more frugal with fuel than either of the other two. On price, the Austin's domestic market recommended retail prices including taxes of £2,424 was significantly higher than the £2,221 charged for the Ford.

Although its performance figures on paper were a little underwhelming, the testers were impressed with the roominess and roadholding of the Austin 2200. They found it quiet and comfortable, the driving position in particular representing a vast improvement over the car's predecessor. They mentioned in passing that the boot/trunk on the test car "leaked slightly", but did not labour the point.

The Princess was similar in size to the Ford Cortina, and was marketed by British Leyland as a rival to the larger engined versions of the Cortina, as well as smaller engined versions of the Ford Granada.

By September 1975, the process of unifying Austin and Morris dealerships was advanced sufficiently, while the Wolseley marque was to be abandoned. Thus the policy of selling seven 18–22 series models under three different marques was changed and the range was reduced to four models all sold under the Princess name. A crown badge was affixed to the point of the bonnet and the script word "Princess" was affixed to the grille, the thick vinyl-clad C-pillars and the boot. Only the 1800 model bore the twin headlights, with the 2200 models sporting the wedge-shaped headlights Harris Mann had designed the car to be seen with.

Build quality of the Princess was affected by poor quality control and constant industrial disputes; it gained a reputation for unreliability it could never shake off, even though quality improved in later years. The styling, praised upon introduction, was soon labelled "ugly". To quote a phrase in Parker's Car Price Guide from the 1990s, "an early critic suggested that the people responsible for designing the front and rear of the car were not speaking to one another".

In July 1978, the Princess was given a revamp and renamed the Princess 2. The main change was the replacement of the 1800 cc B-series engine with the new O-series engine. The new engine was offered in two sizes: 1695 cc and 1993 cc. Since there was an 1800 cc tax barrier for company cars at the time, the 1700 cc O-series engine was developed to take advantage of that, whilst the 2000 cc engine was developed for the private motorists who wanted something different from the hugely popular Ford Cortina. The car had perhaps reached its pinnacle when the prestigious Motoring Which publication described the Princess 2200HLS automatic model as "An excellent car, marred only by poor reliability".

Production of the Princess ceased in November 1981.

The basic Princess design lived on in revised form until 1984 as the Austin Ambassador.

In New Zealand the car was officially sold as the Austin Princess. Assembled in the New Zealand Motor Corporation's plant in Nelson, it was introduced to the market in 1977 and utilized the Austin 1800 B-series engine.

In early 1979 the car was re-engined with the BL O-series OHC motor. Due to a conflict of the Austin Princess and Morris Marina competing in the same market sector in New Zealand, the Princess got a 2.0 L unit mounted transversely, while the Marina (which was face-lifted at that time and renamed in NZ as "Morris 1700") received the 1.7 L unit mounted longitudinally.

Complete article available at this page.